Sdc 918 EntryCheck Manuel d'utilisateur télécharger pdf

Features

Keypad programmable

500 user codes

1 to 6 digit user codes

4 independent outputs

4 independent timers

2 Form C relay contacts

2 solid state open collector outputs

Program entry codes to activate one or

two relays

Disable input

Door sense input

Request-to-exit/enter input

Keypad tamper lockout

Timed anti-passback

Anti-tailgate

Two LED status indicators

Tactile key feel

Audible code entry verification

12 or 24V, AC or DC operation

The 918 EntryCheck™ is a digital keyless entry system designed for

access control applications. The keypad is mounted on a rugged,

stainless steel faceplate and is designed to be mounted in a standard

single-gang electrical box. The indoor backlit keys have bright, easy-

to-read graphics.

Up to 500 entry codes, from 1 to 6 digits in length, can be programmed.

They can activate either, or both of the relay outputs. The “anti-

passback” feature prevents using the same code again before the

programmed time elapses.

All system indicators are long-lasting, solid state LEDs. Two indicators

show the status of the entry system. The left indicator lights red to

indicate power, then turns green when access is granted. The right

indicator lights yellow when the keypad is in “lockout” condition (from

too many incorrect code entries). The yellow LED flashes when the

keypad is in programming mode. An internal sounder beeps when each

key is pressed. An internal jumper sets the sounder volume high or low

The SENSE input can be used two ways. If programmed for “door

sense” the input is wired to a normally closed switch on the door to

detect when the door is opened or closed. Forced entry or door ajar

situations can then be detected. Using door sense, the “Auto-relock”

feature will prevent “tailgating” by turning off the Main Relay output

immediately when the door is closed after access has been granted. If

the SENSE input is programmed for “inhibit”, the input can be wired to a

“service” switch or automatic timer that will disable the Main Relay when

required.

The REQUEST-TO-EXIT input can be wired to a pushbutton to provide

codeless activation of Main Relay, Auxiliary Relay, Output #3 or Output

#4 (programmable).

The ALARM SHUNT output activates when access is granted. This

output can be wired to shunt alarm contacts on the access door/gate to

prevent triggering of an alarm when authorized access occurs.

The 918 EntryCheck™ is powered from a 12-24V AC or DC source.

The EEPROM memory retains all entry codes and programming, even

without power. An internal jumper is provided to reset the master code.

The Main Relay has a 5 Amp capacity. The Auxiliary Relay has a 2

Amp capacity. Two solid state outputs, capable of switching 100 mA to

common, are programmable to signal forced entry, door ajar, lockout,

alarm circuit shunting, request-to-exit, and keypad active conditions.

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

P:\INSTALLATION INST\Access Controls\INST-918\INST-918.vsd REV A 03-12 Page 1

INSTALLATION INSTRUCTIONS

918 ENTRY CHECK

801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •

www.sdcsecurity.com • E-mail: service@sdcsecurity.com

SPECIFICATIONS

Mechanical

Dimensions: 3.00" W x 4.75" H x 1.50" D

(.250”D wall extrusion)

Electrical

Input Voltage: 12-24 Volts AC or DC

Operating Current: 30 mA typical, 150 mA max

Output Ratings

Main Relay: Form “C” 5 Amps @ 28 Volts max

Auxiliary Relay: Form “C” 2 Amp @ 28 Volts max

Type: Solid state outputs (Outputs #3 & #4)

Short-to-common 100 mA @ 24 VDC maximum

Environmental

Temperature: -22°F to 149°F (-30°C to 65°C)

Humidity: 5% to 95% non-condensing

1 2 3 4 5 6

Résumé du contenu

Page 1 - 918 ENTRY CHECK

FeaturesKeypad programmable500 user codes1 to 6 digit user codes4 independent outputs4 independent timers2 Form C relay contacts2 solid state open col

Page 2

P:\INSTALLATION INST\Access Controls\INST-918\INST-918.vsd REV A 03-12 Page 2QuickStart ProgrammingTo enter Programming Mode, enter #9# p

Page 3 - RESISTOR

KEYPAD WIRINGSee Fig. 3 for an example of a basic door installation. The keypad is mounted adjacent to the door. An electric door strike is mounted

Page 4

FACTORY DEFAULTSMaster Programming Code………..………………….….…...123456 Entry Code Length……………………………………….……..4 digitsRequest-to-exit Output Relay………………………..

Page 5 - (Typical Programming cont.)

Select Door Sense or Inhibit Input Default: Door SenseThe input (gray wire) can be programmed for DOOR SENSE or INHIBIT.Press: 1 0 # Input #Input=0

Page 6

Beep Sounds During Auxiliary Relay Default: NoSelects whether or not the keypad beeps during Auxiliary Relay activation.Press: 4 2 # Sound # Sound=1

Commentaires sur ces manuels

Pas de commentaire

Sdc 918 EntryCheck Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Sdc 918 EntryCheck. SDC 918 EntryCheck User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Sdc 918 EntryCheck