Sdc LR100DXK DETEX ELECTRIC LATCH RETRACTION DEVICE KI Manuel d'utilisateur télécharger pdf

P:\INSTALLATION INST\SWITCH KITS\INST-LR100DXK.vsd REV C 10-13 Page 1

INSTALLATION INSTRUCTIONS LR100DXK

DETEX ELECTRIC LATCH RETRACTION DEVICE KIT

MODELS: 10, 20, 40, 50, 60 & 80 SERIES

801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •

www.sdcsecurity.com • E-mail: [email protected]

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

STEP 3

Re-install Pushpad assy. Slide the LR100DXK into the device and

attach the linkage to the clevis. Back the assembly out until the

linkage JUST makes contact with the clevis. Secure in place with the

two #8-32 socket set screws supplied. Wire the unit to power and

replace the Cover, End Cap Mounting Plate and End Cap.

ELECTRICAL DATA

24VDC @ 700/200mA

RED (+) BLK (-)

PATENT PENDING

STEP 2

Install the linkage from the bottom of the

Pushpad assy. Place the spacer over

the existing tapped hole inside the base

where shown. Carefully place the screw

and washer over the linkage and spacer

and tighten into the Pushpad base.

NOTE Retro-Fitting Vertical Rod Devices:

Before retro-fitting an electric latch assembly into a vertical device, the following must be done to

ensure proper alignment. Disconnect the vertical rods from the device head. Install the electric

latch assembly as shown above. Once the ELR is properly installed energize it so that the push pad

is dogged down, by doing so it will allow for proper alignment for the vertical rods. Finally reconnect

the vertical rods to the device and make the proper adjusments.

#10-24

WASHER

LINKAGE

SPACER

#8-32

SOCKET

SCREWS

Back assembly out until

the linkage JUST makes

contact with the clevis

STEP 1

Carefully remove the Cover, End Cap and

End Cap Mounting Plate. If present, remove

existing Dogging. Slide Pushpad assy. out

of the Extrusion and Inner Sleeve.

STEP 2

Pushpad assy.

Exterior Extrusion

Inner Sleeve

Cover*

End Cap Mtg. Plt.

End Cap

*Value Series REQUIRES a

modified cover; either order

Detex Part #100518-11 or modify

existing cover per page 2

1 2

Résumé du contenu

Page 1 - *Value Series REQUIRES a

P:\INSTALLATION INST\SWITCH KITS\INST-LR100DXK.vsd REV C 10-13 Page 1 INSTALLATION INSTRUCTIONS LR100DXKDETEX ELECTRIC LATCH RETRACTION DE

Page 2 - Remove metal inserts

P:\INSTALLATION INST\SWITCH KITS\INST-LR100DXK.vsd REV C 10-13 Page 2Use small wire cutters to snip off all the ribs.Cut out the front wall

Commentaires sur ces manuels

Pas de commentaire

Sdc LR100DXK DETEX ELECTRIC LATCH RETRACTION DEVICE KI Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Sdc LR100DXK DETEX ELECTRIC LATCH RETRACTION DEVICE KI. SDC LR100DXK DETEX ELECTRIC LATCH RETRACTION DEVICE KIT 10, 20, 40, 50, 60 & 80 SERIES User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Sdc LR100DXK DETEX ELECTRIC LATCH RETRACTION DEVICE KI